Box Contents:
- Front brake lines x 2
- Rear brake lines x 2
- Banjo bolts x 4
- Crush washers x 8
Installation Instructions
* Brake line installation should be performed by a professional mechanic. Please read the installation instructions thoroughly and follow them carefully.
Raise the vehicle. Remove the wheels and drain all brake fluid. Carefully remove the existing brake lines from the vehicle, taking care not to spill brake fluid onto painted surfaces. Note the locations of the C-clips and banjo bolts (if used). Remove all crush washers from the mating surfaces. The new kit includes all necessary OEM replacement adapters and banjo bolts.
Clean all sealing surfaces and ensure they are in good condition.
Starting from the caliper, fit these lines by following the original path of the OEM lines. Use the new crush washers included in the kit. Ensure all locating tabs and mounting brackets are properly attached to the mating points on the frame or chassis, and that there is no tension on either end of the connections. Do not fully tighten any bolts or screw ends until the final step of installation.
Check that the line lengths are correct. Ensure the hoses are not twisted or kinked. The torque lines of the opposite axes must remain parallel along the entire length of the hose. You must check the full range of motion of the suspension and steering to ensure the hoses are not stretched or pinched.
Tighten the banjo bolts and end fittings. When tightening these hoses to the factory hard lines, you must use the correct size wrench to hold the hard lines in place. Bolts and end fittings should be tightened to the manufacturer's recommended torque specifications. If unavailable, tighten to 12–14 ft-lbs.
You are now ready to bleed the brakes. You must use new DOT-approved brake fluid and bleed the system according to the vehicle manufacturer's recommendations.
Warning
Before test-driving the vehicle, perform a final check of the lines to ensure all connections are secure and leak-free. The brake pedal should feel firm at this stage. After the first 100 miles of driving, recheck all lines and connections to ensure they are secure and leak-free.
- Mixing rubber hoses and stainless steel replacement lines on the same brake system is not recommended.
-
Do not apply force, twist, or stretch the stainless steel hose assembly. Doing so may cause failure.
<span> span>
** **
Legal only for use on competition vehicles that are not registered or licensed and cannot be used on public roads or highways. May also be used on other exempt vehicles.
-
<li>
Before Ordering〇 Regarding Import Consumption Tax
At the Shaftoya shopping site, we pay the import consumption tax incurred at the time of import on your behalf, so there are no additional charges beyond the total amount paid at checkout.
〇 Compatibility Confirmation
As our entire product database is based on North American vehicles (USDM), please confirm compatibility with Japanese vehicles (JDM) before ordering. (Please feel free to contact us if you are unsure if the listed product is compatible with your vehicle. Our support team will investigate for you.)
If you place an order without confirming compatibility, we cannot accept returns due to incompatibility.
Please note that even if items are sorted by selecting the year, make, and model on our top page, it does not necessarily guarantee that they will fit a Japanese model vehicle without modification.
All products have been translated into Japanese using translation software. There may be confusing expressions, so please contact us before ordering if you have any questions.
○ Regarding Delivery
Shipping costs are paid at the time of settlement. An estimate for shipping can be calculated automatically by entering your shipping address on the checkout page. For large items such as body parts, the actual shipping cost may occasionally differ significantly from the amount calculated automatically. In such cases, we will contact you individually via email.
Basically, all products are shipped internationally from our U.S. warehouse. Unlike domestic shipping in Japan, international shipping takes about 7 to 14 days, so please order with enough time to spare. If you are in a hurry, please contact us in advance to confirm the delivery date. Note that all products are transported by air. They are not shipped by sea.
○ Regarding Japanese Vehicle Inspection (Shaken) Compatibility
Basically, all products handled by us are designed and manufactured outside of Japan. Please note that they do not comply with the "Japanese vehicle inspection system," and we cannot provide documents such as strength calculation reports for the Japanese inspection system. Therefore, all parts are sold for the purpose of "use on circuits, private land, or off-road," and installation and use are at your own risk.
○ Regarding Warranty
Please check the contents immediately upon arrival. Since all products are shipped internationally from outside Japan, there may be shipping damage to the packaging or the product. Please understand that we will only provide returns, refunds, or replacement exchanges if notified within 7 days of receipt regarding products with shipping damage, defective products, or items different from your order. Furthermore, for products sold through us, we will handle all warranty matters "only through us." Please note that we do not coordinate with other companies or agencies located within Japan.